LED Chandelier for roof vent

by Greg Zimmerman
Published: Last Updated on

This LED chandelier adds lots of needed light in a Casita. This made in-the-USA light by Heng’s is available in 4 versions: clear or frosted lens and “cool” or “warm” light.  The warm clear is my favorite as the “cool” is a little harsh on the eyes. It works on both the older Fan-Tastic and newer Maxx-air fans.

The installation isn’t quite “plug ‘n play” and I consider this to be a “medium” to “difficult” mod.  There’s quite of bit of parts juggling overhead.  If you’re coordinated and up for a challenge, follow along as I install one. A helper comes in handy although I manage it solo.

The first step is to pull the fuse from the converter panel that powers the ceiling fan.  Carefully remove the round screen. Next remove the screw in the crank handle knob and remove the knob.  All the Phillips screws holding the fan in need to come out.  The fan will hang from it’s wires.

With a step bit, drill a 7/16″ hole in this location for the push button switch. It will just fit. Insert the switch and screw on the knurled ring.

Now for the fun part. One of the black wires from the switch goes to the black wire on the LED light. Using a yellow Posi-tap, splice the other black switch wire into the black fan wire BEFORE it goes to the 3 speed resistor/fan speed switch (otherwise the fan speed will change the brightness of the light!). The white wire from the light taps into the fan’s white wire. Again into a section of wire that goes from the Casita to the fan, not a wire after the 3 speed switch.

Before assembling the fan, insert the fuse and try the light to ensure it works. If it does, it’s time to button it up. Carefully put the fan back in place, tucking the wires between the inner and outer shells of the fan housing. Tuck the lighting wires up so there’s just enough slack for the light bezel to fit up against the fan. Insert the Phillips screws that hold the fan, but don’t tighten them all the way down.

Have 4, short #6 stainless screws ready to go. Tighten up the fan, hold the light into position, and carefully attach the light with the 4 screws by letting them self-drill into the plastic trim of the fan. Don’t over tighten, just a little snug. Reattach the knob and enjoy your new lighting!

Parts and Tools needed:

  • 2 Yellow Posi-taps
  • 1 blue inline crimp connector
  • 4 short #6 screws (1/2″ long)
  • Wire stripping and crimping pliers
  • Phillips screwdriver or screwgun
  • Step bit

17 comments

Alan October 6, 2020 - 1:17 am

Hi, Greg! I did this mod with a wireless remote that allows me to vary the lighting intensity from 25% to 100%, as I’m laying in bed. There’s a YouTube video showing installation on a Class-A, that’s pretty good. Thanks for your tips!

Reply
Bobbie Shaw October 5, 2021 - 11:18 pm

Im wondering what Other type and size of wire splicing connectors (like wire nuts, could be used besides the Yellow Posi-taps? And should wire nut alternatives be siliconed? I could not find posi-taps at my hardware store.

Reply
Allen May 21, 2023 - 11:35 pm

Do you have a link for the dimmer you bought

Reply
Frank Knight June 2, 2021 - 10:31 pm

Greg! Thank you for this excellent write-up. I’m the kind of guy that needs to see a wiring diagram to make sure I’ve got the wires attached correctly. Your explanation was so clear, I made my own wiring diagram, then installed my light correctly the first try. Thanks again!

Reply
Bobbie Shaw October 5, 2021 - 11:19 pm

Im wondering what Other type and size of wire splicing connectors (like wire nuts, could be used besides the Yellow Posi-taps? And should wire nut alternatives be siliconed? I could not find posi-taps at my hardware store.

Reply
Greg Zimmerman October 6, 2021 - 2:03 am

Posh-taps have to be mail ordered pretty much. You can use crimp connectors. Wire nuts aren’t really used for DC stranded wire. Also you need to splice the power wires, so at a minimum use scotch-locks like Casita’s uses. They are at the hardware store.

Reply
Bobbie Shaw October 5, 2021 - 11:20 pm

Also, which Fuse in the converter panel operates the ceiling fan?

Reply
Greg Zimmerman October 6, 2021 - 2:02 am

I pull one at a time until the fan stops running.

Reply
JEFF HANNEL March 8, 2022 - 2:19 pm

Hi Greg, I installed one of these and when I put the 15-amp fuse back in it worked great. When I turned it off it blew the fuse. Checked the polarity and it was correct. Figured it was the lamp so I got another and had the same problem. In both cases the fan was off when the fuse blew. I tried reversing polarity and blew another fuse. The fan works great both before and after the attempted installations. Should I try a stronger fuse?

Reply
Greg Zimmerman March 8, 2022 - 5:06 pm

Definitely do NOT upgrade the fuse, that can cause a fire. If the fuse is blowing, something is shorted out. Double check everything. Look for a pinched white wire possibly around the frame of the fan. Odd that’s the fuse is blowing while switched off.

Reply
Rick McCarren August 11, 2022 - 4:30 pm

I just finished with the chandelier. Looks great and was a fairly easy install even for one person thanks to your instructions.
I do have a question on another topic.
I believe the electric element in our hot water heater is burned. We bought the SD used so it wasn’t me. When I test for continuity I don’t get a reading. My question is what size is the socket needed to take out the element? I spent a lot of time on the forum but couldn’t find an answer. Thanks for your help.

Reply
Lois A McKee May 3, 2023 - 5:45 pm

Thought I followed all instructions. It does not work. Where did I go wrong?

Reply
Greg Zimmerman May 3, 2023 - 5:56 pm

Let’s work through this via email instead of comments on the web page. I’l help you out.

Reply
Lois A McKee May 3, 2023 - 5:46 pm

I have pictures. Not sure how to send.

Reply
Patricia Blackstock February 4, 2024 - 3:33 pm

Interested in the remote chandelier. Please list link

Reply
Greg Zimmerman February 4, 2024 - 3:37 pm

I’m unaware of a Heng’s brand RV light that has the remote. Maybe an overseas knockoff. The Heng is made in the USA and I don’t mind reaching up for the push button. Less to go wrong.

https://amzn.to/48W69EG

Reply
Mike L March 6, 2024 - 7:25 pm

Couple notes that may help others:

– I bought t-taps from Home Depot instead of the PosiTaps and they work
– Don’t need a step bit. You can just drill a small hole first and then incrementally drill it out a bit larger.
– For my ‘07 there was no fuse labeled for the overhead fan. Mine ended up being tied into the far left 15A water pump fuse.

Reply

Leave a Comment

Adblocker Detected

Ad blockers remove the social media links, contact us info, and the newsletter sign up button from our site.